23.2 C
Tuesday, July 16, 2024

Wireless-N WiFi Repeater Won’t Get IP Address? Let’s Fix!

Must read

To function properly, the Wireless-N WiFi repeater needs to get the IP address from the host router. However, if it doesn’t happen, the user might run into trouble. If you have also done Wireless repeater setup and your device is not receiving IP address, then you have reached the right post.

Here, we will share a few troubleshooting tips using which you can get the problem fixed. So, let’s get started.

Fixed: WiFi Repeater Won’t Get IP Address

  1. Connect WiFi Devices Properly

Start troubleshooting the problem by mending the connection between your Wireless-N repeater and the host router. It must be finger-tight if you have connected them using a network cable. Additionally, the networking cable must not be worn-out from any point. Know that signals will get disturbed due to outer noise if the network cable is not damage-free.

In case you haven’t connected your WiFi devices using a wired source, then the distance separating them must not be too much. If it is, then consider bringing them closer. Remember that closeness never means that your WiFi devices need to get stuck. This might open the door for new Wireless-N WiFi repeater issues.

  1. Reboot Your WiFi Repeater

Being a member of the networking family, Wireless –N WiFi repeaters are also likely to fall victim to technical glitches. Technical glitches are unexpected errors that possess the power of nullifying your repeater’s performance. So, don’t wait to let that happen and reboot your Wireless-N repeater to rid it of technical glitches.

Also, rebooting will erase the cache of the activities that your Wireless-N repeater was performing previously. To reboot your Wireless repeater, simply switch off the power supply for a while and switch it on back. Now, check whether the extender is now receiving the IP address.

  1. Relocate Your WiFi Repeater

After setting up the repeater, it is suggested to move it to a new location in order to fill every dead zone with a high-speed internet connection. But, it seems that something draw your attention while placing the repeater and you ended up selecting the wrong location. Thus, to do Wireless-N WiFi repeater troubleshooting, you need to change the location of your device.

The ideal location of your Wireless-N repeater is somewhere in the center of your house. But, this is not the only criterion that decides the repeater’s performance. You also have to ensure that the space chosen is well-ventilated and free of reflexive surfaces, electronic gadgets, devices operating on Bluetooth technology, metal appliances, and utensils carrying a large amount of water.

  1. Remove Additional Devices

Sometimes, the issue you are facing occurs due to the number of devices accessing your Wireless-N repeater. Perhaps, it is exceeding the limit decided during the Wireless-N repeater setup process.

To get the problem fixed, consider removing all the extra devices that are accessing your Wireless-N WiFi repeater. Now, check whether the repeater has started getting the IP address or not.

  1. Reset and Reconfigure

If all of the troubleshooting tips mentioned above have not helped you enough, then there are high chances that there is something wrong with the setup process. Therefore, you need to get rid of all the customized settings of your Wireless-N repeater. For this, you need to reset your Wireless-N repeater and reconfigure it thereafter. Given below is the outline of the process of resetting the Wireless-N repeater:

Make sure that your Wireless repeater is getting a non-fluctuating power supply from the wall socket.

Find the Reset button on your WiFi repeater and push it.

Wait for the configuration on your Wireless repeater to get deleted.

As soon as your device starts running on the factory default mode, consider setting it up again via the WiFi repeater login page. This time your Wireless-N repeater will surely be able to obtain the IP address from the host router.

The Bottom Line

It is very essential for the repeater to obtain the IP address from the router. Else, you will face connectivity issues. From the tips mentioned above, we can conclude that a lot of factors determine whether your Wireless-N repeater will get the IP address or not.

From the weak connection between WiFi devices to the improper extender setup, you need to identify the correct reason behind the problem and mend your ways. Signing off with the aspiration that the steps discussed in this post will help you fix the issue you were facing like a pro. Thanks for reading the article.

- Advertisement -spot_img

More articles

- Advertisement -spot_img

Latest article